How variable-jet carburettors work

in Basics

Variable jet - SU type

The SU is the simplest type of variable jet carburettor, the other main type, the Stromberg, has a rubber diaphragm instead of a piston.

A carburettor mixes fuel and air in the proportions and quantity the engine needs at any time.

It does this by spraying the fuel into the moving air stream through a jet , so that the fuel vaporises and makes an explosive mixture.

The faster an engine runs, the more air it sucks in. The air passes through a narrowed neck inside the carburettor (called a venturi ), which speeds up its flow at that point.

As air flows faster its pressure drops, so there is a slight vacuum inside the venturi. The fuel jet opens into the venturi, and the partial vacuum sucks fuel through the jet into the air stream.

The speed of the engine is controlled by a throttle, a movable circular flap linked to the accelerator pedal which partly blocks the venturi to admit variable amounts of air.

There has to be some way of governing the fuel flow through the jet so that the mixture is right so that the fuel is in the right proportion to the air. The simplest way of doing this is with a variable jet.

The variable-jet carburettor

The fuel jet is partly blocked by a tapered needle, which can be raised progressively to unblock it.

The needle is fixed to a piston , which is free to slide up and down in a chamber above the jet. The top of the chamber is linked to the inlet manifold through a narrow passage.

Low vacuum in the piston chamber.
At full throttle the throttle butterfly is fully open
Operating the choke lowers the jet, which allows more fuel to be drawn in.

When the engine is idling, low manifold depression and a light spring causes the piston to sit at the bottom of the chamber, and the needle almost completely blocks the jet. Little fuel flows.

As the throttle opens, air flow to the engine increases. The engine speeds up and sucks in yet more air.

This suction creates a partial vacuum in the inlet manifold, and therefore also in the top of the chamber, which is connected to it.

The vacuum is more powerful than the slight vacuum in the venturi under the piston, so it draws the piston up, unblocking the jet and letting more fuel flow.

A sudden burst of acceleration causes a sudden rush of mixture into the inlet manifold, so that the vacuum there lessens for an instant.

That would allow the piston to fall, closing the jet and weakening the mixture; but the problem is avoided by having an oil-filled damper attached to the piston, which prevents it from moving quickly. Therefore, the mixture does not suddenly become too weak for smooth combustion .

Starting from cold

An engine needs an extra-rich mixture more petrol, less air for starting from cold.

On some variable-jet carburettors, this is provided for by the jet being lowered a short way, so that it is less blocked by the needle and dispenses more fuel than usual.

On others, neat fuel is atomised by the rotation of a disc of progressively larger-sized holes.

On a fixed-jet carburettor (See How the fuel system works - fixed-jet carburettors ) the opposite happens: instead of more petrol being supplied to the carburettor, the air supply is partly blocked off by a choke flap above the throttle.

However, both systems are referred to as 'choke' mechanisms, or cold-start enrichment systems.

On some cars you have to set the choke yourself before starting, usually by means of a pull-push control in the dashboard , or steering column or floor pan .

Other cars have an automatic choke which uses a bimetallic coiled strip a strip made of two different metals brazed together attached to the choke lever .

When the engine is cold, the choke is 'on'. As the engine warms, so does the strip.

It expands with heat, but one of the metals expands more than the other, so that the coiled strip bends and uncurls and progressively moves the choke lever to 'off.

The float chamber

For a carburettor to maintain a steady fuel flow, it needs to draw on a supply of fuel which is always kept at the same level.

That supply is provided by a float chamber attached to the carburettor. The float chamber contains a pivoted float which bears against a needle valve through which fuel enters the chamber.

Read more

How the fuel system works - fixed-jet carburettors

The fixed-jet carburettor resembles the simpler variable-jet type (See How variable-jet carbur...

How the ignition system works

The purpose of the ignition system is to generate a very high volt age from the car's 12 volt ...

How engine timing works

For an engine to work at its best, the fuel /air mixture in each cylinder must fire just as ...

How the steering system works

The steering system converts the rotation of the steering wheel into a swivelling movement of t...

We're making the ultimate video course.

Start watching →

You can preview the video course here